ICIGB100-130Watt AC-DC OPEN FRAME POWER CONVERTER
SINGLE & MULTIPLE OUTPUTS

Selection Guide

FEATURES

• Small size 3.00" x 5.00" x 1.28"
• Greater than 80% Efficiency
• 100-130W with Convection Cooling
• Single & Multiple Outputs
• Open Frame Converter
• Wide Input Voltage 90 to 264VAC, 47 to 63Hz.
• Internal EMI filter
• Power Factor Correction
• Output Voltage Protection/Crowbar design
• Input Surge Current
• Over Voltage and Overload Protection

Input specifications:

Parameters	Conditions	Min	Typical	Max	Units
AC Input Voltage		90	100-240	264
Input Frequency		47	50/60	63	Hz
DC Input Voltage		127		370	Vdc
Inrush Current	115Vac/230Vac			30/60	A

Output Specifications:

Set Point Accuracy	V1 +/-1%,V2 and V3 +/-5%, Measured at 60% Load
Output Power	To 130Watt
Minimum Load	No Minimum Load Required (Note 1)
Line Regulation	+/-0.5% for Nominal Line +/-10%
Load Regulation	+/-1%, +/-5% for all secondary Outputs on Multiple Output Models
Tolerance	+/-1
Ripple & Noise	+/-1, Mvp-p
Transient Response	4% max deviation, 500 uS Recovery Time for a 25% Load Change
Temperature	O.5%

General Specifications:

Efficiency Typical	>80% Nominal Line full load
Power Density	6.3 Win3 single Output Models
MTBF	100,000 Hours
Size	3.00 x 5.00 x 1.28"/1.35" for multi-output
Weight	300 grams
Operating Temperature	Minimum: -20C, Maximum: +70C
Storage Temperature	Minimum: -45C, Maximum: +85C
Isolation Voltage	3000VAC Input to Output
Isolation Voltage	1500VAC Input to Ground
Isolation Voltage	500VAC Output to Ground
Safety & EMC	Meets UL 1950

Coefficient Specifications:

Hold Up time	Typical/16, Units/mS
Remote sense	On V1 only, compensates for 0.5V lead drop
Overvoltage	115% to 140% Protection recycle input to reset
Overcurrent	120%-150% Foldback
Protection	With auto recovery

Notes:

1. .20% minimum load required on V1 to maintain stated regulation for auxiliary rails.
2. Load regulation of auxiliaries is defined over the range of 60% of rated output +/-40%.
3. Ripple & Noise is measured by using 20 MHz bandwith, each output terminated with a 0.47 uF capacitor and a 47 uF electrolytic capacitor at rated load and nominal line.

Notes:
1.Input connector mates with Molex housing 09-50-3051 and Molex 2478 series crimp terminal.
2.Output connector mates with Molex housing 09-50-3101 and Molex 2478 series crimp terminal.

TB2	Models
Pins	PS05	PS12, 15, 24 48	PT31	PT30
1	+V	+V	+5V	+3.3V
2	+V	+V	+5V	+3.3V
3	+V	+V	+5V	+3.3V
4	+V	RET	RET	RET
5	RET	RET	RET	RET
6	RET	RET	RET	RET
7	RET	N/A	RET	RET
8	RET	N/A	+12V	+5V
9	N/A	N/A	+12V	+5V
10	N/A	N/A	N/A	+12V

PO BOX 668, South Easton, MA 02375
Email:sales@internationalcoil.com